Tire Tyre Recycling shredder Machine Equipment

The tyre shredder uses high hardness and wear-resisting alloy electrode to surfacing the knife disc edge, the service life is long, can repair the cutting edge repeatedly to grind to use, uses the cycloidal needle WHEEL reducer, has the bearing capacity big, the efficiency is high, the noise is low, the volume is small, the weight is light, the service life is long and so on the advantage, is suitable for each kind of CAR TIRE, truck tire and so on the waste rubber product.

The tire shredder is specially designed for the tire with larger volume, thickness and hardness. Can effectively tear rubber tires, bias tires, radial tires, Car Tires. Shredded tires can be used through the mill equipment, grinding into powder, reprocessing. The tire shredder can directly crush any steel wire tire with diameter less than 2000mm without any prior treatment of the tire. It can directly crush the mouth ring steel wire to improve production efficiency and save labor cost.

Product introduction

Tire shredder is a professional shredding waste tires of mechanical equipment, using the principle of shear, can tear up the whole waste tires into 5-8cm rubber blocks, so as to smash later reuse or directly use. Tire shredding machine is my factory technical personnel on the basis of introducing and absorbing foreign advanced technology, accumulated many years of manufacturing experience, independent research and development design and production of a green waste recycling renewable shredding equipment, has a uniform discharge, tore up the advantages of high efficiency, large capacity, reliable performance, can be widely used in waste recycling industry.

Principle of equipment

Tire shredding machine tool is made of special alloy steel (high speed steel or tool steel) by special processing technology, with good wear resistance, high strength, can be repaired, etc. The driving part is driven by heavy-duty star gear reducer, which has the characteristics of low speed, large torque and low noise. Strong rotating shaft of large Angle hexagon column, so you can safely input large pieces of raw materials, automatic detection overload protection and reverse and other functions.

Characteristics of the equipment

1. 11 knives are installed on the tire shredding machine, 44 movable knives are installed on the rotating knife shaft, and the movable knives can be used on both sides, remove and change the Angle after being blunt, and then sharpen the knives after being blunt on both sides.
2. As it is claw type moving knife, rotary cutting, and fixed knife and moving knife are the material of SKD11 imported from Japan, the hardness of which reaches HRC60° after heat treatment, so the service life is long, the cutting ability is strong, the productivity is high, the normal use of more than 1000 tons need to sharpen the knife.
3. Equipped with conveyor belt, second-stage crusher, steel wire separator, nylon separator and grinding machine, so as to achieve automation, rationalization and labor-saving.
4. Effectively reduce labor intensity and improve working environment.

Safety rules:

1, after starting, for the machine to run properly,  allowed uniform continuous feed crops.
2, pay attention to the speed of the motor, when working  voice and the temperature of the bearing.
3. When feeding, the operator should stand on one side of the feeding mouth, tighten the sleeves of the clothes, and wear a mask and working cap.
4, feeding, attention should be paid to inputs if there is a stone inside, sickle,  tools with hard objects, such as screw, in order to avoid damage to the machine and cause accidents.
5. No belt hanging, oiling, cleaning and troubleshooting are allowed when the machine is running.
6, found the following problems should be shut down the engine, stop processing, motor smoke, crush quality is not good, bearing overheating, more than 60 degrees.

Strictly prohibited items:

1. It is strictly forbidden to peep into the machine from the upper part of the broken cavity during operation.
2. electrical equipment should be connected to the ground, wire insulation should be reliable and installed in the steel pipe laying.
3. It is strictly forbidden to move or remove materials directly by hand in the crushing cavity behind the feeding port during operation.
4. the mill in the operation of any adjustment, cleaning or maintenance work is strictly prohibited.

Pre-sale:
(1) selection of equipment type.
(2) Design and manufacture products according to the special requirements of customers.
(3) training of technical personnel for clients.
(4) The company plans the site for the user free of charge, designs the suitable process and the plan.
On sale:
(1) acceptance of the product.
(2) assisting clients in the preparation of construction plans.
After sale:
(1) assign special after-sales service personnel free of charge to guide customers to install and debug.
(2) installation and debugging of equipment.
(3) on-site training of operators.
(4) after the installation of the complete set of equipment, the full-time technical personnel may assist the customer in on-site production until the user is satisfied.

Contact us if you need more details on Tire Shredder Machine Equipment. We are ready to answer your questions on packaging, logistics, certification or any other aspects about Tire Tyre Shredder Equipment、Tire Recycling Shredder Equipment. If these products fail to match your need, please contact us and we would like to provide relevant information.

Product Categories : Shredder Machine > Tyre Shredder